ULTRASONIC TESTING (UT) ASNT Level 1

Price               : RM 3,000

Duration        : 5 Days

Location        : Puchong Selangor, Malaysia

Apply Now

 

COURSE DESCRIPTION

A course for those who already have basic understanding of the techniques of ultrasonic inspection and are wanting intensive instruction to improve their knowledge and increase their experience. The course is suitable for candidates who are wishing to progress towards any of the examination qualification. The course has a high practical content.

WHO SHOULD ATTEND
This course is opened to all participants, in particular NDT personnel, supervisors, NDT trainers, contractors and researchers and those who are interested in Ultrasonic Testing technique.

COURSE CONTENTS :

SCOPE
This course introduces the basic principles of ultrasonics and prepares the candidate for straight beam inspections and Thickness Measurement. (See Level
II Course Outline for Angle Beam Testing)

This course prepares a candidate
• Select equipment to conduct test
• Setup test equipment
• Steps to conduct test
• Calibration
• Familiarize with codes and standards
• Interpret results with respect to applicable codes and standards
• Understand limitation of the test method
• Write test reports.

TRAINING
Training material is presented in modules that are followed by quizzes

PERSONNEL CERTIFICATION
ASNT SNT-TC-1A
Department of Skills Development (DSD)
Training, experience and examination requirements
Training Requirements
• Recommended Course Outline
• Training Hours
• Practical
• Quizzes and examinations

MODULE 1: MANUFACTURING DISCONTINUITIES
• Types of Discontinuities: Inherent, Processing and Service
• Casting Discontinuities: Hot Tear, Cold Shut, Porosity, Shrinkage
• Primary Processing Discontinuities including discontinuities in Rolling,
   Forging, Drawing, Extruding
• Secondary Processing Discontinuities including discontinuities in Grinding,
   Heat Treating, Machining, Welding, Plating
• Service Discontinuities: Erosion, Wear, Fatigue, Corrosion, Creep

MODULE 2: WAVE MODES
• Time Period and Frequency
• Wavelength
• Wave Modes including Longitudinal, Shear, Surface and Lamb Waves
• Velocity of Waves
• Calculation of Velocity
• Factors Affecting Velocity - Temperature, Stress

MODULE 3: ACOUSTIC IMPEDANCE
• Acoustic Impedance
• Calculation of Acoustic Impedance
• Reflection and Transmission Coefficients
• Transmission through a layer

MODULE 4: REFRACTION AND REFLECTION
• Reflection and Refraction
• Snell’s Law
• Mode Conversion
• First and Second Critical Angle
• Problems on Mode Conversion
MODULE 5: PIEZOELECTRIC TRANSDUCER
• Wave Interference: Constructive and Destructive
• Sound Field
• Near Field
• Far Field
• Beam Spread
• Problems on Near Field and Beam Spread
• Principles of Piezoelectricity
• Curie Temperature
• Transducer damping
• Bandwidth
• Type of Transducers
• Contact and Immersion Transducers
• Dual Element, Delay Line, Angle Beam Transducer
• Couplant

MODULE 6: PULSER RECEIVER
• Ultrasonic Instrumentation - Analog
• Ultrasonic Instrumentation - Digital
• Time Base
• Pulse Repetition Rate
• Types of Ultrasonic Display – A, B and C Scan
• Gates
• Calibration of Ultrasonic Equipment - Time and Amplitude Linearity (Level II)

MODULE 7: ATTENUATION
• Sound Attenuation
• Causes for Attenuation
• Attenuation Measurement
• Calculation of Amplification
• Laboratory - Measurement of Attenuation

MODULE 8: THICKNESS MEASUREMENT
• Test Modes
• Thickness Measurement
• Thickness Measurement Frequency
• Screen Calibration
• Problems
• Laboratory - Thickness measurement, Corrosion Mapping

MODULE 9: IMMERSION TESTING
• Advantages and Limitations of Immersion Testing Technique
• Minimum Water Path calculation
• Types of Immersion Testing Transducers

MODULE 10: FLAW DETECTION - 0 DEGREE
• Lamination, Thickness Measurement
• Loss of backsurface echo technique
• ASME Section V, Article 5
• ASTM standard SA-578 Straight Beam Examination

PRACTICALS
• Thickness Measurement
• Lamination Check

EXAMINATIONS
• General
• Specific
• Practical
• Candidates must score a minimum of 70 % in each test

 

 

 

Call Us +603-80607417

No.4 Jalan Utama 1/16, Taman Perindustrian Puchong Utama, 47140 Puchong, Selangor,Malaysia.

Bussiness Hour

Our support Hotline is available 8.30am to 5.30pm a day

Monday-Friday: 8.30am to 5.30pm

Saturday: Closed

Sunday: Closed

Contact Us

About Us

Established in 2003. Mainly focused on the training activities such as Non-destructive Testing (NDT), Welding, Painting & coating and American Petroleum Institute (API) courses.

The need of skills,qualified and experienced personnel to carry out inspection and other special task is very demanding.As client work on their quality system, the requirement for training and courses is very critical